Solid state RF microwave amplifier products.

SMX-Series, Solid State RF Power Amplifier

 

10 kHz – 1000 MHz

10 – 1000 watts
Minimum Rated Power
RF Power Amplifier

Amplifier Features:

  • Solid State Design
  • Instantaneous Broadband Frequency range
  • Modular Design Construction
  • Rugged construction & High Reliability
  • Integrated Force Air Cooling
  • Backlit Screen
  • Self-diagnostic circuitry
  • IEEE-488 interface & RS232 Remote
 
 

Solid State Amplifier - SMX SeriesInstruments for Industry, SMX-series Amplifiers provide outstanding RF performance. These products are available in a wide range of power levels from 10 watts to 1000 watts in the 10 kHz – 1000 MHz frequency range. These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.

IFI RF amplifiers are very conservatively designed to operate below maximum ratings for ruggedness and long term reliability. Sixth generation LDMOS Transistors provide reliable brute-power performance at frequencies up to 1000 MHz.

Our RF power amplifiers feature individually shielded aluminum assemblies for the module level. This concept of a shielded modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities.

From the ground up, the “SMX-SERIES” products are structurally engineered to withstand operation in mechanically hostile environments. Ruggedized versions are available for applications that will be exposed to very harsh environments.

Model Number Frequency Range
(MHz)
Rated Power
(watts min.)
P1dB Power
(watts min.)
Gain
(dB min.)
kVA Weight
(lbs.)
Size (Inches)
(W x D x H)
SMX10 .01 – 1000 10 10 40 0.1 35 19 x 24 x 5.25
SMX25 .01 – 1000 25 25 44 0.2 40 19 x 24 x 5.25
SMX50 .01 – 1000 50 50 47 0.4 75 19 x 24 x 7.0
SMX100 .01 – 1000 100 80 50 0.5 80 19 x 24 x 7.0
SMX150 .01 – 1000 150 120 52 0.8 120 19 x 24 x 7.0
SMX200 .01 – 1000 200 150 53 1.5 150 (2X) 19 x 27.0 x 10.5
SMX250 .01 – 1000 250 200 54 2 170 (2X) 19 x 27.0 x 10.5
SMX300 .01 – 1000 300 250 55 2.5 180 (2X) 19 x 27.0 x 10.5
SMX400 .01 – 1000 400 300 56 3 200 Rack Integrated
SMX500 .01– 1000 500 400 57 4 250 Rack Integrated
SMX1000 .01 – 1000 1000 800 60 8 750 Rack Integrated

 

Standard Features for IFI SMX-Series Solid State Amplifiers

  • VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open and Short Circuit Protection.
  • * Alternate Prime Power (specify at time of order)
  • GPIB IEEE 488 and RS232 Remote Control
  • RF Sample Port on the Front Panel, 112R for rear panel
  • Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
  • Gain Control Local and Remote, 30 dB range
  • RF Input/Output Connectors on the Front Panel, 118R for rear panel
  • Internal Systems Diagnostics and Status Indicators
  • Total/Operate Elapsed Time Metering in hours
  • RF Safety Interlock
  • Forward/Reflected Power Indication simultaneously on Front Panel display

 

IFI SMX-Series Solid State Amplifier Specifications

  • Input/output Impedance: 50 ohms
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Output Connector: Type N Female. Other connectors available by request or specification
  • Input VSWR: 2.0:1
  • Output VSWR: 2.5:1
  • Operating Temp: 0º to 50º C
  • Non-operating Temp: -40º to 70º C (50,000 feet max)
  • Humidity: 95% without condensation
  • Altitude: 10,000 feet
  • Cooling System: Air cooled, self contained
  • Modulation: AM, FM, Pulse
  • Configuration: Rack Mount as specified in Model Table, or Rack/Cabinet Integrated
  • Spurious Outputs: <-60 dBc nominal
  • Harmonics: -20 dBc minimum @ Linear Power
  • Standard Prime Powers:
    100, 115, 120 VAC ±10% 50/60 Hz, single phase
    220, 230, 240 VAC ±10% 50/60 Hz, single phase
    100/110/115/120 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    200/220/230/240 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    • Special Prime Powers other then listed are subject to availability

Some Available Options for IFI SMX-Series Solid State Amplifiers

  • Option 110-1E: GPIB IEEE-488 RS232 and Ethernet Remote Control
  • Option 110-2: GPIB IEEE-488 and RS 422 Remote Control
  • Option 110-3: GPIB IEEE-488 and RS 485 Remote Control
  • Option 113: Chassis slides for a 19" rack mounting
  • Option 118A: RF Input On Front Output On Rear
  • Option 118B: RF Input On Rear Output On Front

 

SMXL-Series, Solid State RF Power Amplifier

 

10 kHz – 400 MHz

10 – 1000 watts
Minimum Rated Power
RF Power Amplifier

Amplifier Features:

  • Solid State Design
  • Instantaneous Broadband Frequency range
  • Modular Design Construction
  • Rugged construction & High Reliability
  • Integrated Force Air Cooling
  • Backlit Screen
  • Self-diagnostic circuitry
  • IEEE-488 interface & RS232 Remote
 

Solid State Amplifier - SMXL SeriesInstruments for Industry, SMXL-series Amplifiers provide outstanding RF performance. These products are available in a wide range of power levels from 10 watts to 1000 watts in the 10 kHz – 400 MHz frequency range. These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.

IFI RF amplifiers are very conservatively designed to operate below maximum ratings for ruggedness and long term reliability. Sixth generation LDMOS Transistors provide reliable brute-power performance at frequencies up to 400 MHz.

Our RF power amplifiers feature individually shielded aluminum assemblies for the module level. This concept of a shielded modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities.

The “SMXL-SERIES” products are structurally engineered, from the ground up, to withstand operation in mechanically hostile environments. Ruggedized versions are available for applications that will be exposed to very harsh environments.

Model Number Frequency Range
(kHz - MHz)
Rated Power
(watts min.)
P1dB Power
(watts min.)
Gain
(dB min.)
kVA Weight
(lbs.)
Size (Inches)
(W x D x H)
SMXL10 10 - 400 10 10 40 0.1 35 19 x 24 x 5.25
SMXL25 10 - 400 25 25 44 0.2 40 19 x 24 x 5.25
SMXL50 10 - 400 50 50 47 0.4 75 19 x 24 x 7.0
SMXL100 10 - 400 100 80 50 0.5 80 19 x 24 x 7.0
SMXL150 10 - 400 150 120 52 0.8 120 19 x 24 x 8.75
SMXL200 10 - 400 200 150 53 1.5 150 19 x 27.0 x 8.75
SMXL250 10 - 400 250 200 54 2 170 (2X) 19 x 27.0 x 10.5
SMXL300 10 - 400 300 250 55 2.5 180 (2X) 19 x 27.0 x 10.5
SMXL400 10 - 400 400 300 56 3 200 (2X) 19 x 27.0 x 10.5
SMXL500 10 - 400 500 400 57 4 250 (2X) 19 x 27.0 x 10.5
SMXL1000 10 - 400 1000 800 60 8 650 Rack Integrated

 

Standard Features for IFI SMXL-Series Solid State Amplifiers

  • VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open and Short Circuit Protection.
  • * Alternate Prime Power (specify at time of order)
  • GPIB IEEE 488 and RS232 Remote Control
  • RF Sample Port on the Front Panel, 112R for rear panel
  • Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
  • Gain Control Local and Remote, 30 dB range
  • RF Input/Output Connectors on the Front Panel, 118R for rear panel
  • Internal Systems Diagnostics and Status Indicators
  • Total/Operate Elapsed Time Metering in hours
  • RF Safety Interlock
  • Forward/Reflected Power Indication simultaneously on Front Panel display

 

IFI SMXL-Series Solid State Amplifier Specifications

  • Input/output Impedance: 50 ohms
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Output Connector: Type N Female. Other connectors available by request or specification
  • Input VSWR: 2.0:1
  • Output VSWR: 2.5:1
  • Operating Temp: 0º to 50º C
  • Non-operating Temp: -40º to 70º C (50,000 feet max)
  • Humidity: 95% without condensation
  • Altitude: 10,000 feet
  • Cooling System: Air cooled, self contained
  • Modulation: AM, FM, Pulse
  • Configuration: Rack Mount as specified in Model Table, or Rack/Cabinet Integrated
  • Spurious Outputs: <-60 dBc nominal
  • Harmonics: -20 dBc minimum @ Linear Power
  • Standard Prime Powers:
    100, 115, 120 VAC ±10% 50/60 Hz, single phase
    220, 230, 240 VAC ±10% 50/60 Hz, single phase
    100/110/115/120 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    200/220/230/240 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    • Special Prime Powers other then listed are subject to availability

Some Available Options for IFI SMXL-Series Solid State Amplifiers

  • Option 110-1E: GPIB IEEE-488 RS232 and Ethernet Remote Control
  • Option 110-2: GPIB IEEE-488 and RS 422 Remote Control
  • Option 110-3: GPIB IEEE-488 and RS 485 Remote Control
  • Option 113: Chassis slides for a 19" rack mounting
  • Option 118A: RF Input On Front Output On Rear
  • Option 118B: RF Input On Rear Output On Front

 

SCCX-Series, Solid State RF Power Amplifier

 

10 kHz – 220 MHz

10 – 1200 watts
Minimum Rated Power
RF Power Amplifier

Amplifier Features:

  • Solid State Design
  • Instantaneous Broadband Frequency range
  • Modular Design Construction
  • Rugged construction & High Reliability
  • Integrated Force Air Cooling
  • Backlit Screen
  • Self-diagnostic circuitry
  • IEEE-488 interface & RS232 Remote
 

Solid State Amplifier - SCCX SeriesInstruments for Industry, SCCX-Series Amplifiers provide outstanding RF performance. These products are available in a wide range of power levels from 10 watts to 1200 watts in the 10 kHz – 220 MHz frequency range. These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.

IFI RF amplifiers are very conservatively designed to operate below maximum ratings for ruggedness and long term reliability. Sixth generation LDMOS Transistors provide reliable brute-power performance at frequencies up to 220 MHz.

Our RF power amplifiers feature individually shielded aluminum assemblies for the module level. This concept of a shielded modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities.

From the ground up, the “SCCX-SERIES” products are structurally engineered to withstand operation in mechanically hostile environments. Ruggedized versions are available for applications that will be exposed to very harsh environments.

Model Number Frequency Range
(kHz – MHz)
Rated Power
(watts min.)
P1dB Power
(watts min.)
Gain
(dB min.)
kVA Weight
(lbs.)
Size (Inches)
(W x D x H)
SCCX10 10 kHz – 220 MHz 10 10 40 0.1 33 19 x 24 x 5.25
SCCX25 10 kHz – 220 MHz 25 25 44 0.2 35 19 x 24 x 5.25
SCCX50 10 kHz – 220 MHz 50 50 47 0.4 36 19 x 24 x 5.25
SCCX100 10 kHz – 220 MHz 100 80 50 0.5 38 19 x 24 x 5.25
SCCX150 10 kHz – 220 MHz 150 100 52 0.8 40 19 x 24 x 5.25
SCCX200 10 kHz – 220 MHz 200 160 53 1.5 80 19 x 27.0 x 14.0
SCCX250 10 kHz – 220 MHz 250 200 54 2 90 19 x 27.0 x 14.0
SCCX350 10 kHz – 220 MHz 350 280 56 2.5 95 19 x 27.0 x 14.0
SCCX500 10 kHz – 220 MHz 500 300 57 3 100 19 x 27.0 x 14.0
SCCX800 10 kHz – 220 MHz 800 500 60 5 400 Rack Integrated
SCCX1200 10 kHz – 220 MHz 1200 800 62 10 650 Rack Integrated

 

Standard Features for IFI SCCX-Series Solid State Amplifiers

  • VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open and Short Circuit Protection.
  • * Alternate Prime Power (specify at time of order)
  • GPIB IEEE 488 and RS232 Remote Control
  • RF Sample Port on the Front Panel, 112R for rear panel
  • Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
  • Gain Control Local and Remote, 30 dB range
  • RF Input/Output Connectors on the Front Panel, 118R for rear panel
  • Internal Systems Diagnostics and Status Indicators
  • Total/Operate Elapsed Time Metering in hours
  • RF Safety Interlock
  • Forward/Reflected Power Indication simultaneously on Front Panel display

 

IFI SCCX-Series Solid State Amplifier Specifications

  • Input/output Impedance: 50 ohms
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Output Connector: Type N Female. Other connectors available by request or specification
  • Input VSWR: 2.0:1
  • Output VSWR: 2.5:1
  • Operating Temp: 0º to 50º C
  • Non-operating Temp: -40º to 70º C (50,000 feet max)
  • Humidity: 95% without condensation
  • Altitude: 10,000 feet
  • Cooling System: Air cooled, self contained
  • Modulation: AM, FM, Pulse
  • Configuration: Rack Mount as specified in Model Table, or Rack/Cabinet Integrated
  • Spurious Outputs: <-60 dBc nominal
  • Harmonics: -20 dBc minimum @ Linear Power
  • Standard Prime Powers:
    100, 115, 120 VAC ±10% 50/60 Hz, single phase
    220, 230, 240 VAC ±10% 50/60 Hz, single phase
    100/110/115/120 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    200/220/230/240 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    • Special Prime Powers other then listed are subject to availability

Some Available Options for IFI SCCX-Series Solid State Amplifiers

  • Option 110-1E: GPIB IEEE-488 RS232 and Ethernet Remote Control
  • Option 110-2: GPIB IEEE-488 and RS 422 Remote Control
  • Option 110-3: GPIB IEEE-488 and RS 485 Remote Control
  • Option 113: Chassis slides for a 19" rack mounting
  • Option 118A: RF Input On Front Output On Rear
  • Option 118B: RF Input On Rear Output On Front

 

Solid State RF Power Amplifier: SCCXE-Series

 

10 kHz – 250 MHz

10 – 1200 watts
Minimum Rated Power
RF Power Amplifier

RF Solid-State
Amplifier Features:

  • Solid State Design
  • Instantaneous Broadband Frequency range
  • Modular Design Construction
  • Rugged construction & High Reliability
  • Integrated Force Air Cooling
  • Backlit Screen
  • Self-diagnostic circuitry
  • IEEE-488 interface & RS232 Remote
 

Solid State Amplifier - SCCXE SeriesInstruments for Industry, SCCXE-Series Solid State Amplifiers provide outstanding RF performance. These products are available in a wide range of power levels from 10 watts to 1200 watts in the 10 kHz – 250 MHz frequency range. These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.

IFI RF solid-state amplifiers are very conservatively designed to operate below maximum ratings for ruggedness and long term reliability. Sixth generation LDMOS Transistors provide reliable brute-power performance at frequencies up to 250 MHz.

Our RF solid-state power amplifiers feature individually shielded aluminum assemblies for the module level. This concept of a shielded modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities. From the ground up, the “Solid-State SCCXE-SERIES amplifier” products are structurally engineered to withstand operation in mechanically hostile environments. Ruggedized versions are available for applications that will be exposed to very harsh environments.

Model Number Frequency Range
(kHz – MHz)
Rated Power
(watts min.)
P1dB Power
(watts min.)
Gain
(dB min.)
kVA Weight
(lbs.)
Size (Inches)
(W x D x H)
SCCXE10 10 kHz – 250 MHz 10 10 40 0.1 33 19 x 24 x 5.25
SCCXE25 10 kHz – 250 MHz 25 25 44 0.2 35 19 x 24 x 5.25
SCCXE50 10 kHz – 250 MHz 50 50 47 0.4 36 19 x 24 x 5.25
SCCXE100 10 kHz – 250 MHz 100 80 50 0.5 38 19 x 24 x 5.25
SCCXE150 10 kHz – 250 MHz 150 100 52 0.8 40 19 x 24 x 5.25
SCCXE200 10 kHz – 250 MHz 200 160 53 1.5 80 19 x 27.0 x 14.0
SCCXE250 10 kHz – 250 MHz 250 200 54 2 90 19 x 27.0 x 14.0
SCCXE350 10 kHz – 250 MHz 350 280 56 2.5 95 19 x 27.0 x 14.0
SCCXE500 10 kHz – 250 MHz 500 300 57 3 100 19 x 27.0 x 14.0
SCCXE800 10 kHz – 250 MHz 800 500 60 5 400 Rack Integrated
SCCXE1200 10 kHz – 250 MHz 1200 800 62 10 650 Rack Integrated

 

Standard Features for IFI SCCXE-Series Solid State Amplifiers

  • VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open and Short Circuit Protection.
  • * Alternate Prime Power (specify at time of order)
  • GPIB IEEE 488 and RS232 Remote Control
  • RF Sample Port on the Front Panel, 112R for rear panel
  • Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
  • Gain Control Local and Remote, 30 dB range
  • RF Input/Output Connectors on the Front Panel, 118R for rear panel
  • Internal Systems Diagnostics and Status Indicators
  • Total/Operate Elapsed Time Metering in hours
  • RF Safety Interlock
  • Forward/Reflected Power Indication simultaneously on Front Panel display

 

IFI SCCXE-Series Solid State Amplifier Specifications

  • Input/output Impedance: 50 ohms
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Output Connector: Type N Female. Other connectors available by request or specification
  • Input VSWR: 2.0:1
  • Output VSWR: 2.5:1
  • Operating Temp: 0º to 50º C
  • Non-operating Temp: -40º to 70º C (50,000 feet max)
  • Humidity: 95% without condensation
  • Altitude: 10,000 feet
  • Cooling System: Air cooled, self contained
  • Modulation: AM, FM, Pulse
  • Configuration: Rack Mount as specified in Model Table, or Rack/Cabinet Integrated
  • Spurious Outputs: <-60 dBc nominal
  • Harmonics: -20 dBc minimum @ Linear Power
  • Standard Prime Powers:
    100, 115, 120 VAC ±10% 50/60 Hz, single phase
    220, 230, 240 VAC ±10% 50/60 Hz, single phase
    100/110/115/120 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    200/220/230/240 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    • Special Prime Powers other then listed are subject to availability

Some Available Options for IFI SCCXE-Series Solid State Amplifiers

  • Option 110-1E: GPIB IEEE-488 RS232 and Ethernet Remote Control
  • Option 110-2: GPIB IEEE-488 and RS 422 Remote Control
  • Option 110-3: GPIB IEEE-488 and RS 485 Remote Control
  • Option 113: Chassis slides for a 19" rack mounting
  • Option 118A: RF Input On Front Output On Rear
  • Option 118B: RF Input On Rear Output On Front

Specfications are subject to change without noticification © IFI-2011

SCCXL-Series, Solid-State RF Power Amplifiers

 

10 kHz – 100 MHz

10 – 1200 watts
Minimum Rated Power
RF Power Amplifier

Amplifier Features:

  • Solid State Design
  • Instantaneous Broadband Frequency range
  • Modular Design Construction
  • Rugged construction & High Reliability
  • Integrated Force Air Cooling
  • Backlit Screen
  • Self-diagnostic circuitry
  • IEEE-488 interface & RS232 Remote
 

Solid State Amplifier - SCCXL SeriesInstruments for Industry, SCCXL-Series Amplifiers provide outstanding RF performance. These products are available in a wide range of power levels from 10 watts to 1200 watts in the 10 kHz – 100 MHz frequency range. These state-of-the-art solid-state power amplifiers are specifically designed for laboratory and all testing applications.

IFI RF amplifiers are very conservatively designed to operate below maximum ratings for ruggedness and long term reliability. Sixth generation LDMOS Transistors provide reliable brute-power performance at frequencies up to 100 MHz.

Our RF power amplifiers feature individually shielded aluminum assemblies for the module level. This concept of a shielded modular design minimizes internally produced EMI signal leakage and provides easy access for field service and rapid turnaround at depot level repair facilities.

From the ground up, the “SCCXL-SERIES” products are structurally engineered to withstand operation in mechanically hostile environments. Ruggedized versions are available for applications that will be exposed to very harsh environments.

Model Number Frequency Range
(kHz – MHz)
Rated Power
(watts min.)
P1dB Power
(watts min.)
Gain
(dB min.)
kVA Weight
(lbs.)
Size (Inches)
(W x D x H)
SCCXL10 10 kHz – 100 MHz 10 10 40 0.1 33 19 x 24 x 5.25
SCCXL25 10 kHz – 100 MHz 25 25 44 0.2 35 19 x 24 x 5.25
SCCXL50 10 kHz – 100 MHz 50 50 47 0.4 36 19 x 24 x 5.25
SCCXL100 10 kHz – 100 MHz 100 80 50 0.5 38 19 x 24 x 5.25
SCCXL150 10 kHz – 100 MHz 150 100 52 0.8 40 19 x 24 x 5.25
SCCXL200 10 kHz – 100 MHz 200 160 53 1.5 80 19 x 27.0 x 14.0
SCCXL250 10 kHz – 100 MHz 250 200 54 2 90 19 x 27.0 x 14.0
SCCXL350 10 kHz – 100 MHz 350 280 56 2.5 95 19 x 27.0 x 14.0
SCCXL500 10 kHz – 100 MHz 500 300 57 3 100 19 x 27.0 x 14.0
SCCXL800 10 kHz – 100 MHz 800 500 60 5 400 Rack Integrated
SCCXL1200 10 kHz – 100 MHz 1200 800 62 10 650 Rack Integrated

 

Standard Features for IFI SCCXL-Series Solid State Amplifiers

  • VSWR Reflected Power Protection, the unit operates without damage or oscillation into any magnitude of phase or load impedance, Open and Short Circuit Protection.
  • * Alternate Prime Power (specify at time of order)
  • GPIB IEEE 488 and RS232 Remote Control
  • RF Sample Port on the Front Panel, 112R for rear panel
  • Internal Pre-amplification to obtain rated output power with an input level of 0 dBm or less.
  • Gain Control Local and Remote, 30 dB range
  • RF Input/Output Connectors on the Front Panel, 118R for rear panel
  • Internal Systems Diagnostics and Status Indicators
  • Total/Operate Elapsed Time Metering in hours
  • RF Safety Interlock
  • Forward/Reflected Power Indication simultaneously on Front Panel display

 

IFI SCCXL-Series Solid State Amplifier Specifications

  • Input/output Impedance: 50 ohms
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Input/ Sample Connectors: Type N Female, unless specified otherwise
  • RF Output Connector: Type N Female. Other connectors available by request or specification
  • Input VSWR: 2.0:1
  • Output VSWR: 2.5:1
  • Operating Temp: 0º to 50º C
  • Non-operating Temp: -40º to 70º C (50,000 feet max)
  • Humidity: 95% without condensation
  • Altitude: 10,000 feet
  • Cooling System: Air cooled, self contained
  • Modulation: AM, FM, Pulse
  • Configuration: Rack Mount as specified in Model Table, or Rack/Cabinet Integrated
  • Spurious Outputs: <-60 dBc nominal
  • Harmonics: -20 dBc minimum @ Linear Power
  • Standard Prime Powers:
    100, 115, 120 VAC ±10% 50/60 Hz, single phase
    220, 230, 240 VAC ±10% 50/60 Hz, single phase
    100/110/115/120 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    200/220/230/240 VAC ±10% 50/60 Hz, three phase Wye or Delta power is available
    • Special Prime Powers other then listed are subject to availability

Some Available Options for IFI SCCXL-Series Solid State Amplifiers

  • Option 110-1E: GPIB IEEE-488 RS232 and Ethernet Remote Control
  • Option 110-2: GPIB IEEE-488 and RS 422 Remote Control
  • Option 110-3: GPIB IEEE-488 and RS 485 Remote Control
  • Option 113: Chassis slides for a 19" rack mounting
  • Option 118A: RF Input On Front Output On Rear
  • Option 118B: RF Input On Rear Output On Front

 

Connect With Us Here...

  • Facebook Page: 166434726735166
  • Linked In: company/instruments-for-industry
  • Twitter: #!/IFI_Amplifiers
  • YouTube: user/IFIAmplifiers

Instruments For Industry

903 South Second Street • Ronkonkoma, NY
(631) 467-8400 • Fax: (631) 467-8558 
© 2008 All rights reserved